2020-2026+ Porsche 911 Carrera (992) CCB Big Brake Kit | Brembo OEM Porsche 911 GT3 6-Piston
Official Warranty: 1‑year free replacement for quality defects or coating issues under normal (non-track) use.
We Ship Worldwide
2020-2026+ Porsche 911 (992) Carrera / S CCB Big Brake Kit — Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper Front + Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper Rear Setup
992 Carrera and Carrera S owners usually shop this kit after repeated heat fade on fast road or track days, heavy iron-rotor dust on open wheels, or the cost of replacing worn Porsche carbon-ceramic parts through the dealer. This StopFlex upgrade pairs a Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper with a 410mm front carbon-ceramic rotor and a GT3 4-piston rear caliper with a 390mm rear rotor for higher thermal capacity, lower rotating mass, and cleaner wheels. Each kit is built to the confirmed 992 Carrera or Carrera S trim, wheel package, and hub geometry instead of assuming every 992 chassis shares the same brake mounting dimensions.
- 410mm front and 390mm rear carbon-ceramic rotors require 21-inch or larger wheels; wheels below 21 inches will not clear the front rotor package.
- The front axle uses the exact Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper specified for this kit, matched to StopFlex rotor hats and trim-specific mounting hardware.
- Porsche brake pad wear sensors are retained, so the factory pad-wear warning system continues to operate without dashboard errors.
Fitment Hard Lines
| Field | Specification |
|---|---|
| Vehicle | Porsche 911 (992) Carrera / S |
| Model years | 2020-2026+ |
| Front setup | Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper / 410mm |
| Rear setup | Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper / 390mm |
| Page type | Complete CCB kit upgrade |
| Minimum wheel size | 21" (for the 410 mm front rotor) |
Every StopFlex kit is bespoke-engineered for your exact model and trim — the brackets, rotor-hat offsets, and caliper mounting are matched to your specific car, not assumed from the platform. This matters because trims that share a chassis name can differ mechanically: a pure M or performance variant often carries different front knuckles/uprights, hub geometry, and wheel axial (ET) clearance than the standard models in the same family, so a bracket and hat offset that bolt onto one are not the same parts that fit the other. StopFlex supplies the calipers, pads, rotor hats, floating hardware, and brake lines as a matched system built to your confirmed trim. Cars with modified knuckles, modified uprights, or non-factory suspension mounting points must be reviewed before ordering and are not treated as direct-fit.
This setup uses a 410 mm front rotor, so the minimum wheel size is 21". Wheels under 21" will not clear the caliper and rotor, and spoke profile and offset affect clearance too — confirm your exact wheels before ordering.
| Wheel Size (Standard) | Disc Range |
|---|---|
| 15" | 260 mm – 285 mm |
| 16" | 285 mm – 300 mm |
| 17" | 300 mm – 330 mm |
| 18" | 330 mm – 355 mm |
| 19" | 355 mm – 380 mm |
| 20" | 380 mm – 400 mm |
| 21" | 400 mm – 420 mm |
| 22" | 420 mm – 440 mm |
Caliper Overview — Front & Rear Balance
Front Caliper (Primary Upgrade)
The front upgrade uses the Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper, giving the 992 Carrera/S a larger multi-piston fixed-caliper layout for more even pad loading and a firmer, more controlled pedal under repeated hard stops. Because the caliper is a genuine Porsche GT3 Brembo unit rather than a generic aftermarket casting, the package uses proven OEM performance hardware with StopFlex-specific carbon-ceramic rotors, hats, brackets, lines, pads, and mounting hardware.
Rear Caliper (Balance)
The rear axle uses the Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper with a 390mm carbon-ceramic rotor to keep rear brake contribution matched to the larger front system. The kit is engineered to retain the 992 electronic parking brake function and the factory Porsche pad-wear sensor logic.
Front & rear, engineered together: The 410mm front and 390mm rear package is engineered as a system so piston area, rotor diameter, pad choice, and rear contribution work together instead of overloading the front axle. Matching both axles is especially important on a rear-engine 911, where braking stability depends on controlled rear brake participation during trail braking and high-speed stops.
Make It Yours — Color & Logo Customization
Every StopFlex kit-upgrade order can be finished with custom caliper colors, a custom caliper logo, and custom rotor hat colors, so the brake package matches your exact build instead of a fixed off-the-shelf look.
- Custom caliper color
- Custom caliper logo
- Custom rotor hat color
Why StopFlex CCB
Lower Unsprung Mass
StopFlex carbon-ceramic rotors are engineered to reduce rotor mass versus comparable iron discs, helping the suspension react cleaner and the steering feel more precise.
High-Temperature Stability
The carbon-silicon-carbide matrix is built for stable braking behavior at temperatures that can push iron rotors into heavy fade.
Rust-Free Rotor Surface
Carbon ceramic does not form orange flash rust after rain, washing, or storage, keeping the visible rotor face cleaner behind open wheels.
Long Street-Service Potential
In normal road use with matched pads and proper bedding, StopFlex CCB rotors are designed for far longer service life than typical iron replacement rotors.
Low Visible Dust
When paired with matched StopFlex pads, the system produces very low visible brake dust compared with conventional iron rotor and pad combinations.
Premium Ceramic-Glaze Appearance
StopFlex's proprietary coating creates a bright, high-end ceramic-glaze finish with subtle glaze texture and a more premium visual character behind open wheels.
Street-Usable Cold Bite
Street Spec and Track-Day Spec rotors are designed for normal first-stop road use, including cold-weather operation. Motorsport Spec is the competition-focused exception.
Continuous Fiber Reinforcement
Long-fiber carbon ceramic construction improves structural strength and thermal durability versus chopped-fiber approaches.
Heat Management Note
Carbon ceramic rotors tolerate extreme surface temperature, but they do not remove every heat-management requirement. During repeated hard stops, heat can still soak into pads, fluid, seals, calipers, wheels, and nearby components. For long track sessions, mountain descents, or sustained aggressive driving, brake cooling and high-temperature fluid are still recommended.
Street / Track-Day / Motorsport Rotor Options
Street Spec
Ceramic coating, cross-drilled face, and large cooling channels.
Best for daily driving and premium street builds that need clean cold bite, low dust, corrosion-free appearance, and long service life.
Track-Day Spec
Ceramic coating, blank face, and honeycomb cooling channels.
Best for fast-road and track-day use where repeated braking stability matters more than maximum visual drilling style.
Motorsport Spec
Uncoated blank face with honeycomb cooling channels.
Best for race-focused builds that run competition pads, high-temperature fluid, cooling strategy, and a proper warm-up window. Not the default street choice.
Package Scope
| Item | Details |
|---|---|
| Front calipers | Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper |
| Front CCB rotors | 410mm |
| Rear calipers | Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper |
| Rear CCB rotors | 390mm |
| CCB brake pads | Matched for the supplied StopFlex carbon ceramic rotors |
| Brake pad wear sensors | Included; 100% compatible with the OEM wear-sensor system. |
| Rotor hats and floating hardware | Vehicle-specific hardware package |
| Brake lines | Included for complete kit-upgrade orders |
| Color customization | Custom caliper colors, a custom caliper logo, and custom rotor hat colors are available for every kit-upgrade order. |
| Order scope | Default listing is full-car set when front and rear are specified. Front-only or rear-only orders can be arranged after confirmation. |
EPB & Rear Caliper Options
This vehicle leaves the factory with an electronic parking brake (EPB) built into the rear brake, so the rear of the kit is built to keep that EPB working. There are two rear paths. The first is a dual-caliper rear: a main performance caliper handles braking while a dedicated EPB actuator caliper is retained alongside it, so the electronic parking brake, auto-hold, and hill-start assist all keep working; on this path the rear performance caliper can be the TTSPORT EP4 / EP4S 4-piston caliper. The second is an EPB-integrated caliper, a single rear caliper with the electromechanical parking-brake motor built in for a cleaner install with fewer parts behind the wheel; on this path the rear is the TTSPORT EP4 / EP4S 4-piston caliper with integrated EPB. Which path fits best depends on your exact trim and EPB configuration, your budget, your appearance preference, and your wheel size and spoke clearance. Confirm your car's rear-brake configuration with StopFlex before ordering so the correct EPB-compatible rear option is built for your kit.
| Rear option | What it is | Rear caliper | Best when |
|---|---|---|---|
| Dual caliper (EPB retained) | Performance caliper plus a dedicated EPB actuator caliper, both fitted on the rear, so the factory electronic parking brake keeps working. | TTSPORT EP4 / EP4S 4-Piston Caliper | You want guaranteed factory EPB, auto-hold, and hill-start behavior preserved. |
| EPB-integrated caliper | A single rear caliper with the electromechanical parking-brake motor built in, for a cleaner install with fewer parts behind the wheel. | TTSPORT EP4 / EP4S 4-Piston Caliper with integrated EPB | You want a cleaner single-caliper rear with full EPB function. |
FAQ
Will this kit fit my exact 992 Carrera or Carrera S?
Fitment is confirmed per vehicle, not assumed from the 992 chassis name. StopFlex matches the brackets, rotor-hat offsets, caliper mounting, brake lines, and hardware to your exact Carrera or Carrera S trim before the kit is built.
What wheels do I need for the 410mm front rotor?
This kit requires 21-inch or larger wheels because the front rotor is 410mm. Wheel diameter is only the first check; spoke clearance, wheel offset, and barrel shape must also be verified before ordering.
Will the electronic parking brake and pad-wear warning still work?
Yes. The 992 Carrera/S electronic parking brake is retained, and this Porsche-specific kit is compatible with the OEM brake pad wear sensor system, so the factory pad-wear warning continues to work without dashboard errors.
Why move from factory iron brakes or worn OEM carbon-ceramics to this StopFlex kit?
The carbon-ceramic rotors reduce brake dust and rotating mass compared with iron rotors while adding heat capacity for repeated high-speed stops. For cars already equipped with Porsche carbon-ceramics, this kit gives a complete caliper, rotor, pad, hat, line, and hardware package engineered around the 410mm/390mm GT3-style setup.
Need Fitment Confirmation?
Send the exact vehicle details, current rotor sizes, and caliper type before ordering.
More Contact Information
We’re here to help! Whether you need expert advice on brake setups, have questions about your order, or just want to share feedback, our team is ready to assist you. Reach out via your preferred channel below, or use the inquiry form.
Get in Touch
Business Hours
Monday – Saturday, 9:30 AM – 6:30 PM (GMT +8)
Current Time:
Follow Us
- Choosing a selection results in a full page refresh.