2017-2026+ Porsche 718 Cayman (982) CCB Big Brake Kit | Brembo OEM Porsche 911 GT3 6-Piston
Official Warranty: 1‑year free replacement for quality defects or coating issues under normal (non-track) use.
We Ship Worldwide
2017-2026+ Porsche 718 Cayman (982) / S / GTS / GT4 RS CCB Big Brake Kit — Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper Front + Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper Rear Setup
The 2017-2026+ Porsche 718 Cayman 982 owner usually looks at carbon ceramic brakes after repeated heat cycles, track-day fade, heavy brake dust on open wheels, or the cost of replacing factory PCCB parts. This StopFlex kit pairs a 410mm front carbon-ceramic rotor with a Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper and a 390mm rear carbon-ceramic rotor with a Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper for higher heat capacity, lower dust, reduced rotating mass, and a full-car brake balance. Each kit is built around the exact Cayman, S, GTS, or GT4 RS configuration, so bracket geometry, rotor-hat offset, caliper position, brake lines, and pad-wear sensor integration are matched to the car being ordered.
- 410mm front and 390mm rear carbon-ceramic rotors give the 718 Cayman 982 a much larger thermal reserve than a typical street iron setup while requiring 21-inch or larger wheels.
- The front axle uses the exact Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper specified for this kit, paired with bespoke StopFlex hats and hardware for the confirmed 982 trim.
- Factory Porsche brake pad wear monitoring remains active because the kit is built with wear sensors compatible with the OEM warning system, with no pad-wear dashboard errors when installed correctly.
Fitment Hard Lines
| Field | Specification |
|---|---|
| Vehicle | Porsche 718 Cayman (982) / S / GTS / GT4 RS |
| Model years | 2017-2026+ |
| Front setup | Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper / 410mm |
| Rear setup | Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper / 390mm |
| Page type | Complete CCB kit upgrade |
| Minimum wheel size | 21" (for the 410 mm front rotor) |
Every StopFlex kit is bespoke-engineered for your exact model and trim — the brackets, rotor-hat offsets, and caliper mounting are matched to your specific car, not assumed from the platform. This matters because trims that share a chassis name can differ mechanically: a pure M or performance variant often carries different front knuckles/uprights, hub geometry, and wheel axial (ET) clearance than the standard models in the same family, so a bracket and hat offset that bolt onto one are not the same parts that fit the other. StopFlex supplies the calipers, pads, rotor hats, floating hardware, and brake lines as a matched system built to your confirmed trim. Cars with modified knuckles, modified uprights, or non-factory suspension mounting points must be reviewed before ordering and are not treated as direct-fit.
This setup uses a 410 mm front rotor, so the minimum wheel size is 21". Wheels under 21" will not clear the caliper and rotor, and spoke profile and offset affect clearance too — confirm your exact wheels before ordering.
| Wheel Size (Standard) | Disc Range |
|---|---|
| 15" | 260 mm – 285 mm |
| 16" | 285 mm – 300 mm |
| 17" | 300 mm – 330 mm |
| 18" | 330 mm – 355 mm |
| 19" | 355 mm – 380 mm |
| 20" | 380 mm – 400 mm |
| 21" | 400 mm – 420 mm |
| 22" | 420 mm – 440 mm |
Caliper Overview — Front & Rear Balance
Front Caliper (Primary Upgrade)
The front upgrade uses the Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper, giving the 410mm front carbon-ceramic rotor a larger, more rigid clamping package than the standard 718 Cayman front brake. Its six-piston layout helps distribute pad pressure across the swept area for a firmer pedal and more consistent engagement during repeated high-speed stops. Because it is a genuine OEM-derived Brembo Porsche GT3 caliper rather than an anonymous aftermarket casting, the buyer gets known motorsport-lineage hardware adapted through StopFlex trim-specific brackets and rotor-hat offsets.
Rear Caliper (Balance)
The rear axle uses a Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper with a 390mm carbon-ceramic rotor so rear torque contribution and stability are engineered with the front upgrade instead of left as a factory mismatch. The 718 Cayman 982 has an electronic parking brake system, and this kit is configured to preserve the factory EPB and Porsche pad-wear sensor functionality when ordered for the confirmed trim.
Front & rear, engineered together: The 410mm front and 390mm rear package is engineered as a four-corner system so pedal travel, thermal capacity, and brake bias are addressed together. That matters on a mid-engine 718 Cayman because a front-only oversized conversion can change balance under trail braking, ABS intervention, and repeated track use.
Make It Yours — Color & Logo Customization
Every StopFlex kit-upgrade order can be finished with custom caliper colors, a custom caliper logo, and custom rotor hat colors, so the brake package matches your exact build instead of a fixed off-the-shelf look.
- Custom caliper color
- Custom caliper logo
- Custom rotor hat color
Why StopFlex CCB
Lower Unsprung Mass
StopFlex carbon-ceramic rotors are engineered to reduce rotor mass versus comparable iron discs, helping the suspension react cleaner and the steering feel more precise.
High-Temperature Stability
The carbon-silicon-carbide matrix is built for stable braking behavior at temperatures that can push iron rotors into heavy fade.
Rust-Free Rotor Surface
Carbon ceramic does not form orange flash rust after rain, washing, or storage, keeping the visible rotor face cleaner behind open wheels.
Long Street-Service Potential
In normal road use with matched pads and proper bedding, StopFlex CCB rotors are designed for far longer service life than typical iron replacement rotors.
Low Visible Dust
When paired with matched StopFlex pads, the system produces very low visible brake dust compared with conventional iron rotor and pad combinations.
Premium Ceramic-Glaze Appearance
StopFlex's proprietary coating creates a bright, high-end ceramic-glaze finish with subtle glaze texture and a more premium visual character behind open wheels.
Street-Usable Cold Bite
Street Spec and Track-Day Spec rotors are designed for normal first-stop road use, including cold-weather operation. Motorsport Spec is the competition-focused exception.
Continuous Fiber Reinforcement
Long-fiber carbon ceramic construction improves structural strength and thermal durability versus chopped-fiber approaches.
Heat Management Note
Carbon ceramic rotors tolerate extreme surface temperature, but they do not remove every heat-management requirement. During repeated hard stops, heat can still soak into pads, fluid, seals, calipers, wheels, and nearby components. For long track sessions, mountain descents, or sustained aggressive driving, brake cooling and high-temperature fluid are still recommended.
Street / Track-Day / Motorsport Rotor Options
Street Spec
Ceramic coating, cross-drilled face, and large cooling channels.
Best for daily driving and premium street builds that need clean cold bite, low dust, corrosion-free appearance, and long service life.
Track-Day Spec
Ceramic coating, blank face, and honeycomb cooling channels.
Best for fast-road and track-day use where repeated braking stability matters more than maximum visual drilling style.
Motorsport Spec
Uncoated blank face with honeycomb cooling channels.
Best for race-focused builds that run competition pads, high-temperature fluid, cooling strategy, and a proper warm-up window. Not the default street choice.
Package Scope
| Item | Details |
|---|---|
| Front calipers | Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper |
| Front CCB rotors | 410mm |
| Rear calipers | Genuine Brembo OEM Porsche 911 GT3 4-Piston Caliper |
| Rear CCB rotors | 390mm |
| CCB brake pads | Matched for the supplied StopFlex carbon ceramic rotors |
| Brake pad wear sensors | Included; 100% compatible with the OEM wear-sensor system. |
| Rotor hats and floating hardware | Vehicle-specific hardware package |
| Brake lines | Included for complete kit-upgrade orders |
| Color customization | Custom caliper colors, a custom caliper logo, and custom rotor hat colors are available for every kit-upgrade order. |
| Order scope | Default listing is full-car set when front and rear are specified. Front-only or rear-only orders can be arranged after confirmation. |
EPB & Rear Caliper Options
This vehicle leaves the factory with an electronic parking brake (EPB) built into the rear brake, so the rear of the kit is built to keep that EPB working. There are two rear paths. The first is a dual-caliper rear: a main performance caliper handles braking while a dedicated EPB actuator caliper is retained alongside it, so the electronic parking brake, auto-hold, and hill-start assist all keep working; on this path the rear performance caliper can be the TTSPORT EP4 / EP4S 4-piston caliper. The second is an EPB-integrated caliper, a single rear caliper with the electromechanical parking-brake motor built in for a cleaner install with fewer parts behind the wheel; on this path the rear is the TTSPORT EP4 / EP4S 4-piston caliper with integrated EPB. Which path fits best depends on your exact trim and EPB configuration, your budget, your appearance preference, and your wheel size and spoke clearance. Confirm your car's rear-brake configuration with StopFlex before ordering so the correct EPB-compatible rear option is built for your kit.
| Rear option | What it is | Rear caliper | Best when |
|---|---|---|---|
| Dual caliper (EPB retained) | Performance caliper plus a dedicated EPB actuator caliper, both fitted on the rear, so the factory electronic parking brake keeps working. | TTSPORT EP4 / EP4S 4-Piston Caliper | You want guaranteed factory EPB, auto-hold, and hill-start behavior preserved. |
| EPB-integrated caliper | A single rear caliper with the electromechanical parking-brake motor built in, for a cleaner install with fewer parts behind the wheel. | TTSPORT EP4 / EP4S 4-Piston Caliper with integrated EPB | You want a cleaner single-caliper rear with full EPB function. |
FAQ
Will this kit fit my exact 718 Cayman trim?
StopFlex does not assume that every 982 chassis uses the same brake geometry. Cayman, S, GTS, and GT4 RS orders are built after confirming the exact trim, brake package, hub/upright configuration, wheel size, wheel offset, and spoke clearance so the brackets, rotor hats, and caliper mounting match that car.
What wheels are required for the 410mm front rotor?
The 410mm front carbon-ceramic rotor requires 21-inch or larger wheels. Wheel diameter alone is not enough; StopFlex also checks spoke clearance against the Genuine Brembo OEM Porsche 911 GT3 6-Piston Caliper before production.
Will the electronic parking brake and pad-wear warning still work?
Yes. The 718 Cayman 982 uses an electronic parking brake, and this kit is configured to retain EPB function at the rear. The kit also uses Porsche-compatible brake pad wear sensors so the factory pad-wear warning system remains active without dashboard errors when installed correctly.
Why choose this over replacing factory iron or PCCB parts?
For a 718 Cayman used on mountain roads, track days, or with open-spoke wheels, the StopFlex carbon-ceramic package targets lower brake dust, lower rotating mass, stronger heat capacity, and lower long-term rotor wear than iron. For cars already equipped with Porsche carbon ceramics, it also provides a bespoke replacement path without relying on dealer-priced PCCB service parts.
Need Fitment Confirmation?
Send the exact vehicle details, current rotor sizes, and caliper type before ordering.
More Contact Information
We’re here to help! Whether you need expert advice on brake setups, have questions about your order, or just want to share feedback, our team is ready to assist you. Reach out via your preferred channel below, or use the inquiry form.
Get in Touch
Business Hours
Monday – Saturday, 9:30 AM – 6:30 PM (GMT +8)
Current Time:
Follow Us
- Choosing a selection results in a full page refresh.